[0.15″ pitch veroboard] Colorsound – Power Boost / Overdriver

Two different effects, shared (almost) the same component layout.

Very lush sounding units I must admit.

As most of effects from Colorsound line classic and adored!

Power Boost was recently reissued by Macari’s with Castledine  Electronics colaboration

Transistor info: Factory schemo shows BC109C’s but AFAIK those ware never seen in reality. What we see usually is BC169B’s or BC349B (and mix of both) in vintage units, and reissues with BC184L (also seen in vintage Powerboost) or BC184C. Use any NPN Silicon’s with similar spec.

Big hug and high fife to monkeyxx from FSB forum for cool mod ideas.

What you get below is two versions of Power Boost named as Early, and Later spec, and an Overdriver. Another three docs contains the same shit, but in different flavor as per monkeyxx instructions – added master volume control, changed drive pot taper.

Taste it, you’ll love it

– Power Boost Early Spec

– Power Boost Later Spec

– Overdriver.pdf


– Power Boost Early Spec (Monkeyxx Mods)

– Power Boost Later Spec (Monkeyxx Mods)

– Overdriver (Monkeyxx Mods)

[Tagboard] Creepy Fingers Effects Si Fuzz Face


Here’s lovely tagboard layout for si fuzz face clone made by Brad from Creepy Fingers Effects for charity auction where 100% of the proceeds of auction will go to Naoto Matsumura and Tomioka’s animals. Very cool initiative and very nice fuzz face layout on single tagboard. Love it!

Small mods in circuit – added 10R resistor between Q2 emitter and fuzz pot plus small ceramic cap 39pF to lower noise and prevent oscilations on higher fuzz settings.

Transistors are TFK BC130c.

Get the project file here [.pdf]


PAGE UPDATE 18/04/2012

Corrected layout updated.

[Tagboard] Os Mutantes Fuzz / Deadpool


Here’s another cool project for ya – Os Mutantes Fuzz (a.k.a Regulus VIII) !

Circuit developed in 70’s by Cesar Dias for Os Mutantes guitarist.

Very unique sounding circuit powered by two silicon NPN transistors. Only one knob – Volume and Filter switch to cut bass response frequency. There’s also silicon diode clipping section for even more distortion and compression.

Get the Os Mutantes Fuzz project file here [.pdf]

Get the Os Mutantes Fuzz schematic here [.jpg]

And here is Deadpool – Os Mutantes fuzz with some mods by madbean.
Visit madbean’s project page for useful info here.

Get the Deadpool project file here [.pdf]


JMI era VOX AC30/6 – circa 1964 replica layout

Before we start!

Bear in mind I’m a passionate only, and I only get started in tube world. It means – I can’t guarantee proper functioning of my amp layouts. You must remember that high voltage stored in – even switched off tube amp can kill!!! Either way, my draw can be good start for your own research, and I hope it will. All my amp layouts are shown here as my private educational journey and historical research, and can’t be used by any as a DIY projects.

Enough blabla-ing… Now the fun stuff.

I was always loving pushed to the limits VOX AC30 tone, and hate the fact that there is no replica layout on the interweb, so I did one. Ow course I’ve fuck it up big time as a newbie… Happily, there was a very kind British Gent, member of my beloved freestompboxes.org who had one of those and was able and happy to help. Richard (is his name) took a lot of his private time to spell me every small detail to complete this documentation, including original grounding scheme. Richard is THE MAN!

Project Revision 6 (09 November 2012):

So I decided to redraw it again. Current layout have the part numbers fixed – now they match factory schematic. Power amp section is now fixed (it wasn’t bad, all connections was right, as per schematic, but the valves was in wrong order, now it’s exact as in vintage units. Valve chart is fixed to, it was really messy before, now the valve layout/numbering matches the real thing. Few other details was also pimped, mainly cosmetic crap…

Project Revision 7 (18 Oct 2013)

Fixed B+ supply to Vib/Trem channel, connection between R39 and R60 was missing. Apart of that – layout is verified. Thanks to Matt (Masco) for locating the problem, and to Charles for project verification

Here’s two layouts in PDF format:

– JMI Era VOX AC30/6 Normal REV7

– JMI Era VOX AC30/6 Bass REV7

Treble Version, redrawed schematic and more text to be fallow

UPTATE: I would like to bring to your kind attention that the AC30 Chassis and faceplates are available at www.valvepower.co.uk – UK Based Retailer. Email Steve for pricing and availability

Tone Bender Family

Tone Bender MK2 Professional revision2

VOX Tone Bender – or JEN Fuzz, those are the same. I made vero layout that matches PCB pattern, for those who (like me) don’t like to play with chemicals at home. Component values matches my JEN unit. I’ve seen some differences in other VOX/JEN units, like 15uF electros, or different input cap values, but the ones listed in .pdf are most common from those I’ve seen. I’ve made my document with Tropical Fish Caps in mind, if you’re going to use other (axial) caps this can be easily modificated, just move the line, and the trace cuts as I did in my clone below. If you need assistance, @ me.

Tone Bender MK1 Vero – description in progress

Tone Bender MK1 on perfboard – exact repro, full off-board shielded wiring. This is the very first one from the whole family, originally build point to point on perfboard.

Tone Bender MK I.V.pdf – Very alike to good old Fuzz Face, but sounds not the same. Replica layout, full off-board wiring with shielded wire, as original – no LED, no power supply socket.

Another MKII variant. Or like I like to call it MK 1-3/4, or  STFU (Short-Circuit-Board Transitional Fuzz Unit). As I said above it’s basically earliest know to mankind MKII, build around of MK I.V vero design. Few components ware added, but still lacks pull-down capacitor on the input. It have unique sound compare to later MK Two’s. Below, two versions available to download, minor differences, but they are exist:

Sola Sound/D*A*M SCB Reissue.pdf – current D*A*M/Macari’s reissue, also known as Blue Meanie

Sola Sound/D*A*M SCB Reissue + 100R Limiting Resistor.pdf – I’ve seen just one unit like this – actually one picture of one unit, but it was easy to draw. Other MK2’s (Marshall Supa-Fuzzes) with limiting resistors I’ve seen always had 100R there (color code is not visible here). AFAIK not many was made, just a couple for Mr.Main own amusements, but worth mentioning

Original Short Circuity 60’s version.pdf – stock, vintage spec

Standard Tonebender Professional MKII, this is the layout of MKII we see most of the times. No surprises here, replica layout, again full shielded wire off-board wiring, no LED, no power supply socket – MKII Professional.pdf

The same as above, the only difference is 15000pF input and output caps resulting deeper tone. This spec is often seen in Sola/D*A*M reissue creations, as well as in some VOX MK2 Pros and Marshall Supa Fuzz. Download .pdf project file here

All presented layout includes full off-board wiring with shielded wire, no LED, no power supply socket – as original!

Here’s MK3 and MK4’s vero layouts. Those was build on PCB’s originally so this is not direct replica. I had mine C-E-B short leg transistors in mine drawing this (you can use any long leg transistors really with no problem), as well as those sexy orange Philips MKT’s. Tropical Fish caps will also fit here nicely.

Tone Bender MKIII – Early Spec

Tone Bender MKIV Later 1970-72 Spec

Tone Bender MKIV 1972-76 Batman Logo

Here’s few more MK3(isch) projects. What’s common to those above is transistor pinout, and overall layout in most of the cases. Those all basically belongs to TBMK3/4 family, so I decided to post them here:

DAM Fuzz Sound MK3

DAM Fuzz Sound Black On Black Limited Edition

DAM Mother Fucker limited custom project – Grease and Smoke sides done as an independent units

Prescription Electronics – Yard Box

Another MKII. This is what I did after moving parts around in DAM Professional MkII I did recently.

Basically this is the same thing than DAM’s discontinued MKII, with on-board Q2 bias trimmer – only smaller. Small enough to fit into B sized hammond brand (or similar) enclosure. Use 0.1″ pitch stripboard, radial ecaps, small raster (5mm) 10nF and 100nF caps like Panasonic SMF, or Xicon Greenies and 1/4W resistors of your flavor, then enjoy Pocket Bender.pdf

Now – Back On Tag! Two new tagboard layouts for Tone Benders.

Tone Bender MKII

Standard schematic, you can build shitload of Bender variants including Marshall Supafuzz Input cap-to-ground can be easily take off the circuity without moving parts around, or use small-ass SPDT to switch it on or kick it out. Layout includes fully shielded off-board wiring and mojo vibe.

Another one is Tone Bender Mk I.V similar apparition, based on standard well know schematic, full offboard shielded wiring

And here is tag board layout for Vox Tone Bender.

UPDATE 25/06/2012:

Here’s universal layout for MKIII/MKIV type tone benders on 20×8 .15″ stripboard with listed part values for most common versions:

Get the pdf project file.

Get the png project file.